 | |  | | | DELTA 34-672 Dado Head Table Insert for 10-Inch Table Saw | | | | | SKU:
34-672 | | In Stock | | Availability:
Usually ships in 1 business days | | | | | | The Delta dado head table insert is designed specifically for use with the Delta 36-600 saw. This insert provides the proper clearance for a molding cutter head, plus proper support for the workpiece -- installing easily using the existing table insert screws. For safety's sake, be sure to use the proper table insert with specialty blades, such as dado sets or molding cutter heads. | | | |
List Price:
| | |
Our Price:
| $11.28 | |
You Save:
| | | Shipping: | Eligible for FREE Super Saver Shipping on orders over $25. | |
*Shipping:
| |
| | |
|
| | Product Details | | Product Length: | 14.5 inches | | Product Width: | 5.75 inches | | Product Height: | 0.15 inches | | Package Length: | 16.8 inches | | Package Width: | 5.4 inches | | Package Height: | 0.1 inches | | Package Weight: | 0.8 pounds | | Average Customer Rating: |  based on 7 reviews |
|  |
| | Features | Designed specifically for use with the Delta 36-600 sawProvides the proper clearance for a molding cutter headGives proper support for the workpieceInstalls easily using existing table insert screwsFor safety's sake, be sure to use the proper table insert
| |
| | Used and New |
| All | |
| $10.26Shipping Free | Used
- Mint | | | $11.28+ $3.99 *Shipping This item is eligible for FREE Super Saver Shipping on orders over $25. | New | | | $12.95+ $6.74 *Shipping | New | | | $12.99+ $7.00 *Shipping | New | |
| New | |
| $11.28+ $3.99 *Shipping This item is eligible for FREE Super Saver Shipping on orders over $25. | New | | | $12.95+ $6.74 *Shipping | New | | | $12.99+ $7.00 *Shipping | New | |
| Used | |
| $10.26Shipping Free | Used
- Mint | |
| |
| | Customer Reviews | Average Customer Review: ( 7 customer reviews )
Write an online review and share your thoughts with other customers.
Most Helpful Customer Reviews
31 of 31 found the following review helpful:
 A Perfect Fit... Apr 15, 2003
I just bought a Delta TS300 10" table saw (use to be called a model 36-600, by the way) and started looking for dado sets and dado inserts. The Delta website is either perfectly useless or outright wrong when it comes to cataloging the correct accessories for each table saw. So I took my standard insert over to my local tool dealer and asked him to match it up with the correct dado insert. It took him all of 30 seconds to figure it out.
The 34-672 Dado Head Insert is the one to get for the following 10" Delta table saw models: TS300, 36-600, 34-740, and 34-670.
And don't be fooled into buying an 8" dado blade set just because the insert opening is big enough for it. If the motor is less than two horsepower (2 HP), then you should stick with a 6" dado blade set. Anything under 2 HP is considered "underpowered" for an 8" dado. Remember, you now have alot more metal spinning on that arbor, so don't burn out a $... motor just to impress your friends and neighbors.
13 of 16 found the following review helpful:
 Make your own. Dec 13, 2007
By Bryant R. Warren
I know, I know...it's for a direct drive saw, yada yada yada. Well, I make some pretty darn nice cabinetry and furniture with the saw, it just takes some patience and a lot of tuning.
As far as the insert, it's terrible by design.
1. It's nowhere near flat (neither is the standard insert)with measured height diffence of .01 from end to end.
2. The mouth is WAY too big for either a 6" or 8" dado set...can you say "tear out?" (same problem with the standard insert)
3. When any significant amount of pressure is placed on the insert, it deflects. (same problem with the standard insert). This makes accurately depthed cuts darn near impossible.
It turns out that the rabbet in the tabletop is within a couple of thousandths of 1/8" deep...use the factory insert as a template to route a piece of 1/8" lexan to size, then epoxy a chunk of 1/2" hardwood or ply to underside and you've got a zero-clearance insert with no deflection. The wooden stiffener does not have to be precisely cut as it sets below the table top...just make the right size to clear the opening, and you'll have to cut reliefs for the two mounting ears (which I no longer use). Use scotch tape to shim the insert to level with the tabletop. I made 5 of these inserts in 1 hour with about $15 worth material.
Even with the limitations imposed by the trunnions and direct drive system on the saw, you'll be amazed and the difference a stiff, level zero-clearance insert makes.
4 of 5 found the following review helpful:
Good dado head table insert, but not as good as a zero clearance insert May 24, 2006
By Luke McKinney
"Delta Woodworker!"
I bought this table insert for my TS300, mainly because I couldn't find any zero clearance inserts on the market made for my saw. The insert does decent, but there's still some tearing out. The insert also doesn't work well if you're trying to put a dado in a thin piece of stock, as the piece is not fully supported. Overall, I'd say it's good enough for the money spent (~ $10), and good enough for the saw you're working with as well (direct drive induction 15A motor).
3 of 4 found the following review helpful:
34-672 Dado Head Table Insert Apr 03, 2009
By Lewis O. Paddock
I have bought the Delta TS350 table saw just a week ago. It didnot come with the dado insert. I ordered and just received the 34-672 dado insert from Amazon, on time and it fits perfectly. The insert is nice and flat. I am very happy that I was able to find this insert for my saw.
0 of 1 found the following review helpful:
Wrong size & unusable Feb 28, 2011
By Bud
Amazon sent me the wrong size insert (too short) and it doesn't seem worth the trouble to return it. The zero clearance insert that I ordered with it seems to be working fine.
See all 7 customer reviews on Amazon.com
| |
| |
| |  | |  |
|
